Show Summary Details

Page of

Printed from Oxford Research Encyclopedias, Physics. Under the terms of the licence agreement, an individual user may print out a single article for personal use (for details see Privacy Policy and Legal Notice).

date: 26 September 2022

Quantum Dots/Spin Qubitsfree

Quantum Dots/Spin Qubitsfree

  • Shannon P. HarveyShannon P. HarveyStanford Institute of Materials and Energy Sciences, SLAC National Accelerator Laboratory, and Department of Applied Physics, Stanford University

Summary

Spin qubits in semiconductor quantum dots represent a prominent family of solid-state qubits in the effort to build a quantum computer. They are formed when electrons or holes are confined in a static potential well in a semiconductor, giving them a quantized energy spectrum. The simplest spin qubit is a single electron spin located in a quantum dot, but many additional varieties have been developed, some containing multiple spins in multiple quantum dots, each of which has different benefits and drawbacks. Although these spins act as simple quantum systems in many ways, they also experience complex effects due to their semiconductor environment. They can be controlled by both magnetic and electric fields depending on their configuration and are therefore dephased by magnetic and electric field noise, with different types of spin qubits having different control mechanisms and noise susceptibilities. Initial experiments were primarily performed in gallium arsenide–based materials, but silicon qubits have developed substantially and research on qubits in silicon metal-oxide-semiconductor, silicon/silicon germanium heterostructures, and donors in silicon is also being pursued. An increasing number of spin qubit varieties have attained error rates that are low enough to be compatible with quantum error correction for single-qubit gates, and two-qubit gates have been performed in several with success rates, or fidelities, of 90–95%.

Subjects

  • Quantum Information

1. Introduction

In the current research toward a quantum computer, one type of quantum bit is the spin qubit formed in quantum dots (QDs), where the logical subspace is a function of the charge carrier’s spin values. There is a zoo of spin qubit varieties spanning different numbers of dots, materials, geometries, and electrons and holes. This article attempts to organize this large variety of qubits, explaining the common framework they share and how each qubit varies the basic components. While electron spins in quantum dots can act as nearly prototypical quantum systems, their semiconductor environment impacts the spin state in several ways, including spin–orbit interactions, electronic band structure effects, and interactions with nuclei. There are also benefits to working in a solid-state system, such as the ease of control and clear path to scaling. This article provides the reader with an understanding of the major types of quantum-dot qubits in semiconductors being pursued today, and therefore it does not include important work that has been done on nanowires (Petersson et al., 2012) and nanotubes (Churchill et al., 2009), for instance, as well as much of the initial work that focused on creating stable quantum dots that can be operated as qubits. Moreover, spin qubits and quantum dots have many different applications, including quantum sensing in defects (Degen et al., 2017) and single photon emission in self-assembled quantum dots (Warburton, 2013), but this article focuses on spin qubits in quantum dots as used for quantum computing. Although quantum dots can be formed with holes, for simplicity electrons will be assumed for the remainder of the article.

Quantum dots were developed after the phenomena of Coulomb blockade was discovered (Averin & Likharev, 1986; Fulton & Dolan, 1987; Larkin et al., 1984) in aluminum tunnel junctions at cryogenic temperatures. In Coulomb blockade, the conductance across a small, isolated metallic system oscillates with the applied gate electrode voltage (to avoid confusion with quantum gate operations, in this article gate electrode is used to refer to the metallic gates used to define and control quantum dots). This occurs because the system is small enough that the electrostatic energy required to add an additional electron is larger than the thermal energy, and the number of electrons within the system, which is known as a single electron transistor, becomes quantized. To form a quantum dot, it is also necessary that the Fermi wavelength of the electrons or holes is of the same order size as the area where the electrons are confined, which leads to an atom-like quantized energy level spacing (Beenakker, 1991). These are typically formed in semiconductors due to the ability to control the charge density with gate electrodes (Ashoori, 1996; Kouwenhoven et al., 2001). There are several approaches to creating quantum dots. One uses structures with two or more layers of semiconductors, known as semiconductor heterostructures, where the electrons are confined to a two-dimensional electron plane. Two distinct varieties of quantum dots are formed with this technique. First are vertical quantum dots (Tarucha et al., 1996), where the quantum dots are confined using etching, then controlled via gate electrodes on the side of the etched region. The second design is referred to as lateral gating, where there are a series of metal gates on the surface on the semiconductor that control the energy of the quantum dot; this has become the dominant technique for quantum dots used in quantum computing. In these quantum dots, the gate electrodes create an approximately parabolic potential in which the electrons are confined. These electrons have a quantized energy spectrum comparable to that of atoms, but because of their larger length scale, from tens to hundreds of nanometers, they have proportionally smaller energy spacing. Another type of quantum dot used for quantum computing is the donor, a single dopant atom with a bound charge in a semiconductor, which is an intrinsically zero-dimensional system, and therefore the gates are needed to control the energies of the various quantum dot states. Laterally gated quantum dots and donor qubits are focused on in this article due to their prevalence in current quantum computing research.

Although there is a wide range of quantum dot–based spin qubits, they share the same basic set of properties. Further complexity is provided by adding additional quantum dots, which allow for more control parameters, and in particular allow the qubit state to be encoded partially in the position of the electrons within the quantum dots, endowing them with a dipole moment. The different architectures and materials each have trade-offs to their controllability, speed, noise, and other properties, which are addressed in the section “Implementations.”

Section 2 on “Quantum Dots” builds a simple model describing their essential properties and explains how they are controlled. Section 3, “Implementations,” explains how quantum dots become qubits, describing the Hamiltonians and control techniques for the major varieties of spin qubits and how they vary across different materials. After discussing single-spin qubits and describing how they work and their early results in gallium arsenide (GaAs)/aluminum GaAs (AlGaAs), the subsections discuss the different types of implementations in silicon, silicon metal-oxide-semiconductor (Si-MOS), silicon/silicon germanium (Si/SiGe), and donors. The remaining subsections cover some of the multiple quantum dot spin qubits, including charge qubits, singlet–triplet and hybrid qubits, and triple-dot qubits. In the final section, “Key Challenges and Technologies,” some topics of marked importance for the future development of spin qubits as a scalable quantum computing platform are discussed.

2. Quantum Dots

This section examines how to isolate a two-level quantum system using quantum dots. The derivation is for layered semiconductors, with donors addressed in the section “Donors.” Electrons are confined to two dimensions due to the layer structure of the semiconductor—at an interface between two different semiconductors as in GaAs/AlGaAs, in a narrow quantum well as in Si/SiGe, or between an insulator and semiconductor (MOS)—with the two-dimensional conducting layer known as a two-dimensional electron gas (2DEG) (Davies, 1998). These layers are typically tens of nanometers below the surface. The material may be doped to accumulate the 2DEG, or accumulation (positively biased) gates may be used to induce it. Gate electrodes on the surface of the material are then used to deplete the electron gas locally around the quantum dot and create a potential well in which the remaining electrons are confined. Drawings showing two variations of a typical set of gate electrodes used to define double quantum dots (discussed further in “Multiple Quantum Dots”) are shown in Figure 1. These gates also have the effect of increasing the resistance between the quantum dot and the 2DEG adjacent to it, which allows the electrons to become localized in the dot (discussed later). The nearby 2DEG is referred to from now on as the leads, a reference to electrical leads, because the 2DEG is the source of electrons tunneling into the quantum dot.

Figure 1. Drawings showing an example of the gate electrodes used to define a double quantum dot “stadium style” (left) and with overlapping gates (right). The different types of gate electrodes are labeled with P for plunger, L for lead, and T for tunnel coupling. The P gates can be thought of as primarily affecting the chemical potential of the dot, and thereby the number of electrons; the L gates as affecting the tunnel coupling between the dot and the leads; and the T gates as affecting the tunnel coupling between dots. The source (S) and drain (D) are colored purple and are regions of 2DEG that represent the leads for the two quantum dots. In the stadium style, which is named such because the gate electrodes surround the region where the quantum dot sits, gate electrodes (green) are typically biased to negative voltages to remove 2DEG locally. In the overlapping style, gate electrodes are deposited in multiple overlapping layers separated by a thin insulator, with the plunger gate electrodes (blue) biased relatively more positively to induce the quantum dots to sit directly under them, and the lead and tunneling gate electrodes (green) are biased more negatively. In undoped systems, it is also necessary to put gates over the source and drain to accumulate a 2DEG to enable tunneling between the QDs and leads, as shown in this sketch in blue.

Figure 2. Schematic of a quantum dot with one gate electrode, which has voltage Vg, and capacitance to the dot (circle) Cg, and total capacitance Cg+Cr. This drawing does not represent the tunnel junctions to the leads for the quantum dot.

The energy of a quantum dot can be calculated by treating it like a metallic object with total capacitance C and charge Q=Ne, where N is the number of electrons it contains. Ignoring tunneling with the leads for the moment, a useful simplified model has one nearby gate with voltage Vg and capacitance to the quantum dot Cg. A schematic of this is shown in Figure 2, where Cr is the rest of the capacitance, Cr=CCg. The energy of this is

U(N,Vg)=(eNeN0CgVg)22C=Ec2(NN0CgVge)2,(1)

where N0 is the number of electrons in the dot when Vg is 0, and Ec=e2/C is the electrostatic cost of adding an electron to the dot or charging energy (van der Wiel et al., 2002). This can be seen by considering the chemical potential, the energy required to add the Nth electron to the dot:

μ(N,Vg)=U(N,Vg)U(N1,Vg)=Ec(NN01/2CgVg/e).(2)

The difference between the chemical potential for adding the N1th and Nth electron is Ec. When μ=0, states with N and N1 electrons have equal energy and another electron can enter the dot. Quantum dots typically have capacitance in the tens or hundreds of attofarad, leading to Ec110meV. When the resistance between the leads and quantum dot R becomes much larger than h/e2, the quantum dot can have a well-defined number of electrons. This can be understood by noting that the tunneling time onto the dot τRC, and therefore through the Heisenberg uncertainty principle, ΔEτ>h, which we can rewrite as ΔE/Ec1 when Rh/e2.

There is also a second energy scale that comes from populating different quantum dot orbitals, which can be understood to be akin to those in atoms. For the electrons to be confined in these states, the quantum dots must be designed to be near the size of the Fermi wavelength of the 2DEG, which is usually tens of nanometers. Although detailed discussion of the orbital states is outside the scope of this article, the comparison to atoms is useful for establishing how electrons in quantum dots can be thought of as isolated, controllable spins. As in atoms, for principal quantum number n>1, the quantum dot states can have non-zero angular momentum, and quantum dots with filled s, p, d, and f shells have been measured (Leon et al., 2020). This article largely focuses on electrons with n=1, although spin qubits with larger numbers of electrons have been studied (He et al., 2019; Higginbotham et al., 2014) to take advantage of increased screening. The energy of the first electron in the quantum dot can be approximated as that of an infinite well, of order 2m*R2, where R is the dot’s radius, and m* is the effective mass. These have been measured to be approximately 0.05–1 meV in GaAs/AlGaAs dots and 1–10 meV in Si/SiGe (Reimann & Manninen, 2002; Zajac et al., 2015). Spin qubits in quantum dots are operated at temperatures well below the point at which excited states become thermally occupied, so the electrons fill the lowest energy states available.

The electrons that are added to the quantum dot come from the leads, which are tunnel coupled to the quantum dot, allowing electrons to hop between the 2DEG and the quantum dot when the energy of an additional electron is at the Fermi level of the 2DEG. It is challenging to form quantum dots that can be fully emptied because removing all of the electrons from a quantum dot requires large negative voltages on the gate electrodes that define it, but these will also have the effect of reducing the coupling to the 2DEG leads to zero, preventing electrons from entering and exiting the dot. To avoid this, the quantum dots must have careful design of gate electrodes, typically by separating the gates into “plunger” gates that mostly control the electron population and “lead” gates that mostly control coupling to the nearby 2DEG (Ciorga et al., 2000). This effect is particularly acute in silicon due to its larger effective mass (Simmons et al., 2007).

By applying a magnetic field in the plane of the quantum dot, Bz, and including spin, the energy of the quantum dot shifts by ±μBgBzSz, where g is the g-factor of the material (g0.44 in GaAs and g2 in silicon), and μB is the Bohr magneton. The primary controllable parameters in this type of quantum dot are the number of electrons in the dot; the tunnel coupling to the leads, which is controlled by the locations of and voltages on nearby gates; and the magnetic field applied to the dot. In reality, of course, the situation is more complicated, with each gate controlling multiple parameters, disorder impacting the voltage the dot experiences, and the location and size of the dot within the gated region impacted by gate voltages (which can be taken advantage of for quantum operations, as discussed in the section “Single-Spin Qubits”). The process of configuring the QD to have the desired properties by shifting the voltages of the gate electrodes that define it is referred to as “tuning” and is often complicated. A great deal of effort has been dedicated to improving the process, which is discussed in the section “Scaling.” The gate electrodes that control the quantum dot may be controllable from DC to microwave frequencies, depending on the wiring.

Typically, the number of electrons in the quantum dot is measured using an adjacent charge sensor, either a quantum point contact (QPC) or quantum dot that is capacitively coupled to the quantum dot and whose conductance is highly sensitive to the charge of the quantum dot (Field et al., 1993). The conductance, typically by measuring the current directly or through RF reflectometry, as discussed further in the section “Readout,” shows a jump at each electron transition. The absolute number of electrons can be measured by fully depleting the dot so that there are no more transitions. These charge sensors are used both in the initial “tuning” process, in which the number of electrons in the quantum dot and other properties are set, and also for measuring the qubit. The techniques used to measure the qubit states are discussed in the sections on “Implementations” and “Readout.”

2.1. Multiple Quantum Dots

A double quantum dot (DQD), which describes two adjacent, tunnel-coupled quantum dots, has a considerably more complicated equation for the potential energy compared to single quantum dots because in addition to there being an additional dot and gate electrodes, the dots also have cross-capacitance. A full derivation is presented in van der Wiel et al. (2002); here, a minimal version is described to give some intuition. The effects of cross-capacitance are ignored because they do not affect the physics but add substantially to the complexity of the equations. Two possible charge states are considered: (0,1) and (1,0), where (m,n) refers to the configuration with m electrons in the left dot and n electrons in the right dot; therefore, this refers to either one electron in the right or in the left dot. Using the model from quantum dots, the gates controlling the chemical potential of each dot are Vg,i; they have capacitance to the dot they control Cg,i; and the dots have total capacitance Ci, N0,i electrons at zero voltage and charging energy Ec,i, i={L,R}. A cartoon of such a system is shown in Figure 3. Their difference in energy is

ΔE=U(0,1)U(1,0)=eCg,LCLVg,LeCg,RCRVg,R+Ec,L/2(1+N0,L)+Ec,R/2(1N0,R).(3)

Here, the important takeaway is that the energy difference between the two states is a linear function of the voltage difference between the nearby gate electrodes. In the case of the multiple dot systems, it is often useful to find a single parameter that describes the important energy scale of the system. For a DQD, that is the “detuning” or difference in potential energy between the QDs, ε,

ΔE=ε=αRVg,RαLVg,L+E,αi=eCg,iCi,(4)

where αi is the so-called “lever arm” for the gate, representing the amount the QD energy shifts when the gate electrode voltage is changed, and which is dependent on the proximity and size of the gate electrode and QD; it can be measured to make quantum dot tuning easier, as discussed in the section “Scaling.” E is a constant voltage representing the four right terms in equation (3). ε is the main control knob in performing experiments (Petta et al., 2005). There is also tunnel coupling between the two dots, which takes the form HT=tc|(1,0)(0,1)|+h.c. In practice, the rate tc can be controlled by adjusting the gates in between the quantum dots to change the potential barrier between the two dots. The energies for this system, centered around the point where the (0,1) and (1,0) states are degenerate, can be written as a Hamiltonian with the basis (0,1), (1,0):

H=(ε/2tctcε/2)Ei=(ε/2)2+tc2,i={g,e},(5)

Where Ei are the eigenstates of the matrix and are plotted as a function of the potential energy difference between the dots ε in Figure 4.

Figure 3. Schematic of a double quantum dot, with each dot having one gate electrode, which has voltage Vg,i, capacitance to the dot (circle) Cg,i, and total capacitance Cg,i+Cr,i, with i={L,R}. This drawing does not represent the tunnel junctions to the leads for the quantum dots or between the quantum dots.

Figure 4. Energy diagram for the (1,0) and (0,1) states of a tunnel-coupled double quantum dot. The relative energy of an electron in the left or right quantum dot changes linearly with the potential energy difference between the dots, ε, as shown by the dashed blue lines. When the electron is allowed to tunnel between the dots, the left and right quantum dot occupation states hybridize, creating a ground and excited state shown in yellow, which have minimum splitting 2tc. For an electron in the ground state, as ε is increased, the electron moves from the left to right QD.

The ground state charge distribution can be derived as QRQL=ε2Eg, where Qi represents the wavefunction weight in each quantum dot. This can physically be thought of as a charge dipole moment that can be controlled with gate electrodes. This approximation, of course, assumes that changing εonly changes the chemical potential of the dot, not the confining potential of the dot itself. Next, spin is included in the model so that the DQD’s state will be represented by the product of its charge and spin state. In addition to the spatially uniform magnetic fields that impact single QDs, in a DQD a magnetic field gradient between the dots also impacts the energy diagram. Therefore, the energy of electrons with the same spin state in the (0,1) and (1,0) will have additional offset of energy equal to gμB/2ΔBz, with ΔBz=BLBR representing the difference in the effective magnetic field experienced by the electrons in each dot (Petta et al., 2005).

The remainder of this section focuses on a DQD with two electrons, which will be the basis for the singlet–triplet qubit (Hu & Sarma, 2000; Levy, 2002). Only the voltage region in which the electrons are in (1,1) and (0,2) is considered, although the analysis applies equally to the (2,0) and (1,1) region. The energy diagram shown in Figure 4 also applies for the charge states (1,1) and (0,2), with (1,1) replacing (1,0) and (0,2) replacing (0,1). Considering only electrons in the ground orbital state, there are four possible combinations of spin states for two-electrons: the singlet state and three triplet states, S=12(||),T0=12(|+|),T+=|,T=|.The Pauli exclusion principle becomes important here because it limits the possible combinations of charge and spin states. The total wavefunction must be antisymmetric, and because the singlet spin state is antisymmetric, the charge states must be symmetric; for example, in (1,1), 12(|LR+|RL), and in (0,2), |RR, where L and R represent the wavefunction for an electron sitting in the left and right quantum dot, respectively. Because the singlet has allowed (1,1) and (0,2) states, its ground state is the same as the ground state in Figure 4, a hybridized (1,1)(0,2) state. The triplet spin states, however, are symmetric, so they must have an antisymmetric charge state, which does not exist for (0,2) if only the ground orbital state is used. This means that although the singlet state can inhabit the ground state of the DQD from the Hamiltonian (equation 5), the triplet states can only be in (1,1), a phenomenon known as Pauli exclusion. The allowed and disallowed combination of spin and charge states are shown for the T0 and S states in Figure 5.

Figure 5. The possible spin states for |S and |T0 in the subspace of (1,1) and (0,2)) charge configurations are diagrammed here. In this case, the charge configuration is represented by the number of spins in a given dot [the top row shows (0,2) states and the bottom row shows (1,1) states]. The states that are allowed have checkmarks and the one that is not allowed has a red X. This indicates that the singlet state can be in either (1,1) or (0,2), but the triplet must be in (1,1).

The energies of the four states as a function of ε are shown in Figure 6. The plot shows that the energy splitting between the |S and |T0 states can be reduced to 0 by setting ε such that both the |S and |T0 are in the (1,1) state, and then can be turned on continuously by increasing ε so that it is energetically favorable for two electrons to be in the right dot. This |S|T0 splitting is known as the exchange energy or J(ε). Eventually, J(ε) becomes large enough that it becomes energetically favorable for one of the electrons in the triplet state to enter an excited orbital state, lifting Pauli exclusion so that it can enter the (0,2) charge configuration (Barthel et al., 2009). An energy diagram showing this for the |T0 state (the |T+ and |T are excluded to improve clarity, but they show the same crossover) is displayed in Figure 7. Because the |T0 state has the same charge configuration as the singlet state in this region, J(ε) is constant at EST0 (Dial et al., 2013). The |S and |T0 states can be distinguished by setting ε so that the triplet states are in (1,1) and the singlet state is localized in (0,2), at which point the different charge distributions can be measured with a nearby charge sensor. Finally, the magnetic field gradient creates an energy splitting between | and | of E=gμBΔBz. Together, this can be written as a Hamiltonian H=J/2(ε)σz+ΔBz/2σx.

Figure 6. Energy diagram for singlet (|S) and triplet (|T,|T0,|T+) states in a DQD with two electrons as a function of the detuning ε. An in-plane magnetic field is applied to separate the triplet states by energy EZ. The singlet is in the ground state of the DQD, while the triplet states are Pauli-blockaded in (1,1).

Figure 7. Energy diagram for singlet (|S) and triplet (|T0 states showing the region of ε (at the right) where it becomes energetically favorable for one of the electrons in the triplet state to enter an excited orbital state, lifting Pauli esxclusion so that it can enter the (0,2) charge configuration. This state is labeled excited T0. The charge configuration is also labeled in the regions where the states are localized in a given charge configuration (i.e., away from the avoided crossings). EST0 is the maximum |S|T0 splitting, constant in the region where both |S and |T0are in (0,2).

3. Implementations

The idea of using quantum dots for quantum computation was first described in Loss and DiVincenzo (1998) and Kane (1998). In the years since, a variety of qubits in quantum dots have been studied, each with its own strengths and weaknesses. Several of the most common ones are discussed in the following sections, which explain how they are defined and controlled, their experimental results, and major challenges they face, in an attempt to give some coherence to a broad field of study.

This article separates spin qubits into two categories—those that use a single quantum dot, described in Section 3.1, “Single-Spin Qubits,” and those that use multiple quantum dots, described in Section 3.2, “Charge Qubits,” Section 3.3, “Singlet–Triplet and Hybrid Qubits,” and Section 3.4, “Triple-Dot Qubits.” Those in the first category can typically be thought of as being primarily defined by their spin state, whereas those in the second category are usually also defined by the location of the spins in the quantum dots, or their charge state. This distinction is important because it determines how they can be controlled and measured, the noise to which they are susceptible, and many of their other key features. In general, the first category of “spin-like” qubits are often controlled by magnetic fields, which poses more stringent requirements on the control lines, but decoupling from magnetic field noise has been more achievable than decoupling from charge noise. The “charge-like” qubits in the second category are more often controlled by using voltages to shift the electron between dots applying a voltage to gates. This has the benefit of being a simple means of control but the disadvantage of coupling the qubit to charge noise, which is challenging to mitigate, as discussed in the section “Decoherence.” However, most qubits are some mixture of the two, and some qubits have been developed to take advantage of the best traits of both spin and charge coupling.

3.1. Single-Spin Qubits

A single electron in a single quantum dot with the logical subspace of | and | may be thought of as the simplest possible spin qubit. These qubits can be controlled by using magnetic resonance techniques to perform electron spin resonance. Applying a static magnetic field to split the energies of the spin states and an oscillating magnetic field perpendicular to the static one at a frequency close to qubit splitting drives oscillations around the Bloch sphere (Slichter, 1990). If the static field is applied in the z direction and the AC field is applied in the x direction, the resulting Hamiltonian is

H=gμBBS^=gμB(Bzσz+Bxσxcos(ωt+ϕ)),

where ω is the AC frequency and ϕ is the phase of the AC signal. Making the rotating frame transformation, for the resonant case ω=gμBBz/, this becomes

Hrot=gμB(Bxcosϕσx+Bxsinϕσy).

The static magnetic field is typically on the order of 1 T and is applied globally to all qubits. Several techniques have been used to apply the oscillating magnetic field, which can be far weaker in magnitude than the static one and has frequency ranging from approximately 5 to 50 GHz, depending on the experiment. The first technique is to fabricate a coplanar waveguide (CPW) near the qubit, which was first demonstrated in a GaAs/AlGaAs heterostructure (Koppens et al., 2006). However, CPWs can cause substantial heating due to the need to send down large voltages to create fast Rabi rates, and they have a large spatial extent, making it difficult to address single qubits.

It is also possible to generate magnetic fields by applying a voltage with frequency ω to nearby gates to drive the electron spatially within the dot. Experiments using this method in GaAs/AlGaAs relied on the spin–orbit interaction, in which the oscillating electron experiences an effective magnetic field (Nowack et al., 2007). Another way to transmute electron motion into a magnetic field is to fabricate a micromagnet next to the quantum dot (Pioro-Ladrière et al., 2008; Tokura et al., 2006). The micromagnet is designed to have a large magnetic gradient dBxdl, where l is the direction along which the electron is driven, creating the effective field dBxdlδlcos(ωt), where δl is the amplitude of the electron’s motion, which is a function of the voltage applied and the quantum dot’s confining potential. Micromagnets also apply a small but non-zero Bz field, so if there are multiple dots close to one another, this separates the Zeeman splittings, allowing them to be addressed independently.

In experiments in GaAs/AlGaAs, the qubits decohered quickly due to magnetic field noise from uncontrolled nearby nuclear spins. The reduction of magnetic field noise in silicon, particularly with the use of isotopically purified silicon, which has 50–800 ppm residual 29Si (Tyryshkin et al., 2012), has allowed great improvements in such devices, as discussed in the three following sections on Si-MOS, Si/SiGe, and donors. Magnetic field noise is discussed at greater length in the section “Nuclear Noise.” Entangling gates in single-spin qubits typically rely on the exchange interaction, as described in the section “Multiple Quantum Dots.” Exchange-based gates can be extremely fast, but because they are charge-dependent, they couple the qubits to charge noise, which can limit gate fidelity.

It is useful to consider a pulse sequence for a full sequence of qubit manipulation, consisting of loading the initial state, performing oscillations around the Bloch sphere, and reading out the final state. For a single-spin qubit, this can be performed using one high-frequency gate electrode per qubit. To load the qubit in a known state, the gate electrode shifts the qubit energy so that the | state has a lower energy than the lead and the | state a higher energy, so that tunneling between the dot and lead will reset the qubit state to |. Next, the gate voltage is shifted so that the electron is decoupled from the lead, and the quantum gate operation is performed. Finally, readout is performed by first performing the necessary rotation to measure the correct qubit orientation, and then the gate voltage is shifted so that the | state is above the lead energy and the | state is below it, so that electron can tunnel between them only if it is in the | state. The tunneling signal is measured by a nearby sensor, typically a QPC or QD (Elzerman et al., 2004). This process is diagrammed in Figure 8. Currently, there are three major platforms in which these qubits are being developed. The details of their implementations are discussed in the following sections.

Figure 8. The pulse sequence for a single-spin qubit. A magnetic field is applied to separate the spin states by energy EZ (in this figure, g is treated as a positive number). (Left) First, the qubit is initialized in the | state through tunneling with the lead (gray). (Middle) Then, a resonant magnetic field is applied to drive oscillation between spin states. (Right) Finally, the qubit is measured through tunneling with the leads.

3.1.1. Si-MOS

In this design, based on the dominant one for modern transistors, an insulator is deposited on silicon, and depletion and accumulation gate electrodes are deposited on top of it (Veldhorst et al., 2014). The silicon is undoped, so the accumulation and depletion gate voltages are adjusted to accumulate a 2DEG at the insulator–semiconductor interface to form quantum dots. This system has increased disorder compared to semiconductor heterostructures due to increased defects in oxides compared to semiconductors and the nonepitaxial interface between the amorphous oxide and silicon, making it more challenging to form quantum dots in the desired location and to have full control over their properties. The use of overlapping gates, as shown in Figure 1, in which gates are deposited in multiple overlapping layers with a thin insulating layer between them to prevent shorting and with some directly over the quantum dot, better defines the potential the quantum dot experiences compared to the original “stadium style,” in which there is a single layer of gates at the perimeter of the quantum dot. It has been instrumental in enabling experiments with these qubits as well as some using Si/SiGe (Angus et al., 2007). The increased effective mass in silicon compared to gallium arsenide decreases the Fermi wavelength, forcing dots in silicon systems to be smaller than those in GaAs; they are typically approximately 50 nm wide, still within the tolerance of electron beam lithography.

One challenge in silicon qubits is valley degeneracy. This arises because silicon has six degenerate energy minima, known as valleys, in its conduction band, and electrons in quantum dots could potentially occupy any of them. To be useful qubits, the degeneracies must be lifted in the quantum dots because small valley splittings (the energy difference between the different valleys) can cause leakage out of the logical subspace and cause T1, the energy relaxation time, to be reduced. Confinement in the z direction shifts the energies of four of those states, and the final degeneracy can be lifted by applying electrical fields—for instance, by gating (applying voltage to nearby gate electrodes)—but it is also affected by roughness and disorder (C. Yang et al., 2013). In Si-MOS, electric fields applied through gating have been effective to create a robust valley splitting of up to 0.8 meV, larger than relevant qubit energy scales. T1 is approximately 1 s and therefore does not limit gate fidelities (C. Yang et al., 2019).

The Si-MOS implementations so far have used coplanar waveguides to perform single qubit gates. Changing the voltage of a nearby gate electrode applies a Stark shift that alters the g-factor at each quantum dot, changing the resonant frequency for each qubit by up to approximately 10 MHz. This enables one to apply a global static magnetic field and then use a single coplanar waveguide to control several qubits independently using multiplexing (Veldhorst et al., 2014). In samples made on isotopically purified silicon, using pulse optimization techniques (C. Yang et al., 2019) has decreased the average single qubit gate error to fractions of a percent, with coherence times of up to 10 ms. Two-qubit gates using exchange have been measured with an average Clifford gate fidelity more than 90%, Rabi rates in the hundreds of kilohertz, and entangling rates close to 1 MHz (Huang et al., 2019). Readout fidelities ranging from approximately 80% to 95% and an integration time of several milliseconds are typical.

3.1.2. Si/SiGe

This system uses a quantum well of silicon, approximately 10 nm thick, between layers of Si1xGex, where x0.3 (Zwanenburg et al., 2013). There are many similarities between Si/SiGe and Si-MOS systems because both are gate-defined quantum dots whose wavefunction is primarily in silicon. Both stadium style gates and overlapping gates have been used for devices in Si/SiGe. Although some devices use doping to populate the 2DEG, it has become more common to use undoped silicon. Finally, although CPWs have been used previously for qubit control, micromagnets are used more often for single qubit gates currently (Kawakami et al., 2013; Yoneda et al., 2017). The valley degeneracy in Si/SiGe is lifted by strain between the Si and SiGe as well as vertical confinement, but small valley splitting can pose a challenge (Kawakami et al., 2014). Adjusting local gate voltages can help lift it (Goswami et al., 2007; Watson et al., 2018).

Using natural silicon and micromagnets, single qubit gate fidelities reach 99% and Rabi rates are approximately 1 MHz (Kawakami et al., 2016). In isotopically purified silicon with improved micromagnet design, 99.9% average gate fidelity and Rabi rates of tens of megahertz have been measured (Yoneda et al., 2017). Two-qubit gates using the exchange interaction have been achieved with gate rates of several megahertz and fidelities of 80–90% in natural silicon (Watson et al., 2018; Xue et al., 2019; Zajac et al., 2018). Improvement in these fidelities could be achieved through reducing the susceptibility to charge noise, as in Zajac et al. (2018), and by working in isotopically purified silicon. Long-distance coupling through a superconducting resonator has also been achieved in Si/SiGe devices and is discussed in the section “Cavity Coupling.” Readout fidelities of 70–85% with integration times of several milliseconds are typical, and they are limited by T1 and temperature.

3.1.3. Donors

Donors are single atoms situated in a semiconductor and possessing bound hydrogen-like charge states. A phosphorus atom in silicon has a bound electron and nuclear spin, both with spin 1/2 (Pla et al., 2012; Tyryshkin et al., 2003), and both can therefore be used as qubits. Bulk donor ensembles have shown extremely long coherence times, with T2=10 s in isotopically purified silicon, indicating that single donors might show similar coherence times (Tyryshkin et al., 2012). The donors are formed either through ion implantation or by positioning them using lithography with a scanning tunneling microscope. The latter technique offers the possibility of precise placement for multiple qubit systems (Weber et al., 2014). In donor-based systems, the gate electrodes are not needed to define the quantum dot potential, as in the other implementations discussed here, and instead are needed only for performing quantum gate operations. The electron state has a Bohr radius of approximately 2 nm, which becomes particularly important in exchange-based operations because the two quantum dots need to be extremely close to another to have non-zero tunneling between them (Y. Wang et al., 2016).

In order to perform initialization and readout, a single-electron transistor is fabricated adjacent to the donor qubit, and it acts as both a lead and a sensor (Morello et al., 2010). Readout has shown fidelities more than 98% (Dehollain et al., 2016). Single qubit gates are performed using a CPW. Measurements of the electron qubit in ion-implanted single donors in isotopically purified silicon have shown the anticipated long coherence times, with T2 of more than 500 ms with dynamical decoupling (Muhonen et al., 2014). Using randomized benchmarking, an average single-qubit gate error of less than 0.05% was measured (Dehollain et al., 2016).

Most proposals for two-qubit gates between donor electrons rely on the exchange interaction, but this can be challenging due to the requirement for donors to be extremely close together because of their narrow wavefunction, especially for implanted donors, which are placed stochastically. Despite this, large exchange couplings have been measured between two ion-implanted electron donors (Dehollain et al., 2014; Gonzalez-Zalba et al., 2014). For scanning tunneling microscopy (STM)-placed donors, it is easier to design specific exchange couplings, but there are still challenges, such as the exchange coupling’s oscillation in magnitude with donor separation due to valley interference (Y. Wang et al., 2016). An exchange gate has been measured with STM donors, with gate speeds approaching 1 GHz (He et al., 2019). A number of ideas for coupling donors that do not require exchange have also been proposed, such as entangling donors with other varieties of qubits, creating hybrid donor laterally gated quantum dot qubits, and using longer range capacitive coupling or cavity coupling (Harvey-Collard et al., 2017; Morello et al., 2020).

The nuclear spin can also be used as an auxiliary qubit, and because it is decoupled from charge, it has shown coherence times of more than 30 s with dynamical decoupling and average gate fidelity of 99.99% (Muhonen et al., 2014, 2015). Entanglement has been achieved between the electron and nuclear spin on a single vacancy, with a Bell state fidelity of 96% (Dehollain et al., 2016). The extremely long-lived states in nuclear spin qubits, combined with their high-fidelity coupling to electron spins, may enable them to act as a quantum memory.

3.2. Charge Qubits

Charge qubits, which have one electron in a DQD, were introduced in multiple quantum dots. Their Hamiltonian is H=ε/2σz+tcσx, with a logical subspace of |R and |L, which represent the electron being in the right or left dot, and the energies of the ground and excited states are shown in Figure 9. The charge distribution of the qubit states can be changed by changing the voltage detuning between the dots ε. When ε is large and positive, they approximately align with the electron being in right and left quantum dots, and Hεσz and vice versa for ε large and negative. At ε=0, the left and right occupation states are degenerate and Htcσx. Therefore, a central difference between charge and single-spin qubits is that charge qubits can be controlled by gate voltages alone, without applying resonant pulses. As shown in Figure 9, the qubit’s splitting changes magnitude and the relative amounts of σx and σz change as the local voltages are changed; this can be thought of as the Bloch sphere vector representing the Hamiltonian rotating and changing length. The minimum splitting for a charge qubit is 2tc, which is typically several gigahertz (Dovzhenko et al., 2011; Gorman et al., 2005; Petersson, Petta, et al., 2010; Shi et al., 2013), and the splitting increases as ε is increased or decreased from zero. Because tc cannot be turned off, there is always a σx component, but by increasing ε so that it is much larger than tc, nearly orthogonal control can be achieved. A second key difference between these and single-spin qubits is that charge qubits are highly coupled to charge noise, stemming from charge fluctuations in the environment and leading to decoherence. Their use in quantum computing applications so far has therefore been limited because of the high speed of electronics required to control them and short coherence times. Charge qubits are important as a prototype for several other types of spin qubits that use multiple quantum dots, such as singlet–triplet and hybrid qubits and triple-dot qubits, which share many properties with charge qubits, but have found ways to mitigate some of the downsides of the charge qubit.

Figure 9. The energy diagram for a charge qubit (bottom figure), with the Bloch sphere for each ε value superimposed on top of it, showing that the vector rotates from being largely in the z direction to the x direction and then to the +z direction.

3.3. Singlet–Triplet and Hybrid Qubits

The singlet–triplet qubit alters the charge qubit to have longer coherence times and the ability to reduce the splitting practically to zero. This reduces the coupling to charge noise enough that higher gate fidelities are achievable, but the gates can still be fast. It has two electrons in a DQD, with the logical subspace being the singlet and triplet zero-spin states. The Hamiltonian is H=J/2(ε)σz+gμBΔBzσx and was introduced in multiple quantum dots.

As in charge qubits, gate operations are performed by changing ε, and the energy diagram is shown in Figure 6. The singlet–triplet qubit has the somewhat unique property of being both a spin and a charge qubit, depending on how it is biased. In the region of values of ε where JgμBΔBz, the singlet–triplet qubit is “charge-like,” with the two qubit states having different charge distributions than one another. Similarly to charge qubits, because ΔBz is constant as a function of ε, there is always a σx component, but J can be set to be much larger than gμBΔBz, so nearly orthogonal control can be achieved. By increasing ε, the exchange energy J can be varied from zero up to tens of gigahertz typically, limited by the point at which it becomes energetically favorable for the triplet state to enter an excited orbital state in the quantum dot it had been Pauli blockaded from, as shown in Figure 7. When J is non-zero, the qubit is coupled to charge noise and the susceptibility to noise increases with J.

At ε0, HgμBΔBzσx, and the two qubit states have the same charge state, only differing in their spin state, so the singlet–triplet qubit is effectively a spin qubit and is largely charge-insensitive. The magnetic gradient value is set either by an effective magnetic field from the nuclei, known as the Overhauser field (more typical in GaAs/AlGaAs), or by a nearby micromagnet (more typical in silicon qubits). In the case in which the gradient arises from the nuclei, it fluctuates in time but can be fixed to values from megahertz to gigahertz using dynamical nuclear polarization and a feedback method with T2*100ns (Bluhm et al., 2010; Nichol et al., 2017). Micromagnets have lower noise but are less changeable in situ. Due to the low-frequency character of nuclear noise, dynamical decoupling is extremely effective, with T2 increasing to close to 1 ms with notch filtering of the Larmor frequencies in GaAs/AlGaAs (Malinowski, Martins, Nissen, et al., 2017), as discussed in the section “Nuclear Noise.”

Initializing the qubit state uses the same method as single-spin qubits: Using gate electrodes, the energy of |S is set below the energy of the lead and the energy of |T0 is set above it so that tunneling between the quantum dot and the lead loads |S. This can be performed in nanoseconds to high fidelity due to the large singlet–triplet splitting in this region. A quantum dot fabricated adjacent to the DQD so that it is sensitive to the number of electrons in each dot is used for measurement. ε is set to a large positive value where the singlet state is localized in (0,2), while the triplet remains Pauli-blockaded in (1,1). Then, by measuring the number of electrons in each dot, the singlet and triplet states can be differentiated. This charge readout can be quite fast when using a tank circuit in the measurement circuit, with 98% fidelity in 1μs (Barthel et al., 2009; Shulman et al., 2014).

Randomized benchmarking has measured average single qubit gate fidelities of approximately 99.5% in both GaAs/AlGaAs and Si/SiGe (Cerfontaine et al., 2020; Takeda et al., 2020), limited by both charge and nuclear noise. It is possible to tune singlet–triplet qubits to have “sweet spots,” regions in which the first-order coupling to charge noise goes to zero, thereby increasing coherence times (Martins et al., 2016; Reed et al., 2016). The singlet–triplet qubit has been entangled using a capacitive gate, arising from the dipole moment of the DQD when exchange is non-zero (Shulman et al., 2012). The interaction is slower than the exchange gate and limited by charge noise, but using a technique to partially decouple the qubit from charge noise improved to a 90% gate fidelity noise (Nichol et al., 2017).

Hybrid qubits are also formed in DQDs but add a third electron, which yields a Hamiltonian where both axes of control are voltage-controlled so there is no requirement for magnetic fields (Kim et al., 2014). They possess two sweet spots, allowing control around two axes that is decoupled from charge noise, and gate speeds of several gigahertz. Single-qubit process fidelities of approximately 95% have been measured in hybrid qubits in natural Si/SiGe (Kim et al., 2015).

3.4. Triple-Dot Qubits

Fully electronic control can also be achieved by adding a third electron and third dot, forming the triple-dot or exchange-only qubit (Russ & Burkard, 2017). These qubits utilize the exchange between the left and middle dot and the right and middle dot to give two independent axes of control, separated by 120° (Laird et al., 2010; Medford et al., 2013). The qubits therefore have charge states with weight in the (2,0,1), (1,1,1), and (1,0,2) configurations, and the logical subspace is a singlet-like ground state and triplet-like excited state. The Hamiltonian can be controlled either with the detuning between the left and right quantum dots or through tunnel barrier control. These qubits have the advantage of fast gates and no requirement for a magnetic field (although magnetic noise can cause dephasing). Some of their challenges include the requirement for composite pulses due to the nonorthogonality of the control axes, increasing overhead, and leakage to other three-electron states outside the logical subspace. The exchange-only qubit uses spin-to-charge conversion readout like the singlet–triplet qubit.

Initial experiments were performed in GaAs/AlGaAs and were limited by magnetic field noise. More recently, they have been studied in isotopically purified Si/SiGe (Andrews et al., 2019; Eng et al., 2015). In these experiments, a variant of randomized benchmarking meant to capture leakage was performed, showing an average error of 0.3%, with half of the error stemming from leakage, for symmetric gates decoupled from charge noise. Exchange-only qubits in GaAs/AlGaAs, working in the rotating frame, were used to achieve strong coupling to a microwave resonator, as discussed further in the section “Cavity Coupling.”

4. Key Challenges and Technologies

4.1. Decoherence

The number of coherent operations that can be performed by a quantum computer is ultimately limited by decoherence of the quantum system. This is caused by uncontrolled interactions with the environment. In spin qubits, the primary sources of decoherence are magnetic noise and charge noise. This section explains what is known about these noise sources, how they vary across the different spin qubit types, and techniques for reducing the impact of noise on spin qubits.

A useful approximation for modeling the noise that affects spin qubits is to separate it into two categories, quasi-static and high-frequency. Quasi-static noise is constant within a single quantum gate operation but can vary across them. It can be modeled by including a noise term in the Hamiltonian so that H=(H0+dH)σz, where dH follows a Gaussian distribution with standard deviation σ. A simple Ramsey experiment, in which a qubit is initialized in a given state and allowed to evolve under H, has the decay time T2*=h/(2πσ), making it straightforward to extract the magnitude of quasi-static noise in the system. High-frequency noise requires more sophisticated analysis and experiments, such as dynamical decoupling pulses that remove the effects of quasi-static noise. This leaves the qubit susceptible only to noise at higher frequencies, which can in turn be analyzed to extract its power spectral density (Álvarez & Suter, 2011; Cywiński et al., 2008).

4.1.1. Nuclear Noise

In GaAs/AlGaAs heterostructures, the nuclei of Al, Ga, and As all have nuclear spin I=5/2, which generates an effective magnetic field that acts on the qubit through hyperfine coupling (Chekhovich et al., 2013). The noise arising from this nuclear bath was the primary factor limiting coherence in GaAs/AlGaAs qubits for many years (Coish & Loss, 2004; Khaetskii & Nazarov, 2001). The magnitude of the noise does not depend on the magnetic field at the values used in experiments, and generally T2*=1040ns if no correction techniques are employed (Petta et al., 2005; Koppens et al., 2008). Dynamical decoupling experiments have shown that nuclear noise is extremely low frequency, following a power law of S(ω)=S0/ωβ, where β23, and S(ω) is the power spectral density of the noise (Malinowski, Martins, Cywiński, et al., 2017; Medford et al., 2012). This makes it highly amenable to dynamical decoupling, which was shown to increase T2 to 500ns in a single spin qubit with a Hahn echo pulse (the simplest dynamical decoupling pulse, which removes the effects of quasi-static noise) (Koppens et al., 2008), and in singlet–triplet qubits to increase T2 to 200μs (Bluhm et al., 2011) using the more complicated CPMG dynamical decoupling sequence and 870μs using pulses defined to act as notch filters on the Larmor precession of the fluctuations (Malinowski, Martins, Nissen, et al., 2017).

In singlet–triplet qubits, which are sensitive only to the magnetic field gradient, the gradient can be fixed using dynamical nuclear polarization and a feedback method that also increase the coherence time to T2*100ns (Bluhm et al., 2010). Moreover, because the average value of the field gradient can be set to the desired value and only fluctuates slowly, the nuclear field can be measured rapidly using Hamiltonian parameter estimation and qubit operations thereby decoupled from the fluctuations, increasing T2* to 2μs (Shulman et al., 2014). This direct measurement of the nuclear bath finds that it diffuses as a random walk, indicating 1/f2 power spectral density, similar to what was measured through dynamical decoupling. These results indicate that there are many effective approaches to reducing the impact of low-frequency noise.

In natural silicon, 95% of the isotopes are spin zero (28Si and 30Si), and T2* for single-spin qubits in Si/SiGe increases to 1μs and T2 to 40μs (Kawakami et al., 2014; Zwanenburg et al., 2013), and in singlet–triplet qubits T2* increases to 360 ns (Maune et al., 2012). In isotopically purified silicon, which usually has 800 ppm residual 29Si isotopes, T2*=120μs and T2,CPMG=28ms in Si-MOS single-spin qubits, T2*=20μs and T2,CPMG=3.1ms in single-spin Si/SiGe, and T2*=2.3s in Si/SiGe singlet–triplet qubits. Analyses have indicated that nuclear noise is no longer the limiting factor in these coherence times (Chan et al., 2018; Eng et al., 2015; Muhonen et al., 2014; Yoneda et al., 2017), which may also explain why they vary across the different silicon implementations.

4.1.2. Charge Noise

The other major source of noise comes from fluctuating charges near the qubit. Their precise source is unknown, although it has been hypothesized that they stem from charge traps near the surface or in the oxide layer for qubits that have one (Paladino et al., 2014). In most charge-like qubits, the sensitivity to charge noise, which is given by the derivative of the splitting with respect to detuning voltage, is voltage-dependent. This makes quoting a T2* time less useful than with nuclear noise; for instance, in singlet–triplet qubits, the noise sensitivity increases proportionally with the splitting, making the gate fidelity nearly constant with respect to the splitting, although T2* may change dramatically.

Quasi-static noise has been measured in charge, singlet–triplet, and triple-dot qubits, and it has been found to have a similar magnitude across multiple materials, as noted in Harvey-Collard et al. (2017), with σ10μeV (Cerfontaine et al., 2020; Dial et al., 2013; Eng et al., 2015; Shi et al., 2012; Watson et al., 2018). Charge noise is higher frequency than nuclear noise, with most measurements finding a power spectral density of the form S(ω)=S0/ωβ, β1 (Chan et al., 2018; Dial et al., 2013; Struck et al., 2020; Yoneda et al., 2017), making the improvements from dynamical decoupling more limited than with magnetic noise.

Studying the temperature dependence of charge noise may give insight into its origins. Experiments in GaAs/AlGaAs have shown a strong temperature dependence, with T2 changing quadratically with temperature and T2* linearly between 50 and 250 mK. Si-MOS devices measured from 0.45 to 1.25 K do not show temperature dependence in T2*. Measurements of the noise in the current through Si/SiGe quantum dots show an approximately linear temperature dependence from 0.1 to 1 K, but the magnitude and functional form vary from dot to dot (Connors et al., 2019). Considered together, these results may indicate that the smaller size of the devices in silicon compared with GaAs/AlGaAs leads to interacting with a far lower number of fluctuators, changing the statistical properties of the noise. Another interesting direction of such research is studying spatial correlations to noise, although results are currently inconclusive due to competing magnetic noise (Boter et al., 2020).

Increasing gate fidelities limited by charge noise has taken two main directions. The first direction is to reduce the qubit’s sensitivity to charge, but this often also has the secondary impact of slowing quantum gates, and it requires ingenuity to find ways so that this does not ultimately reduce the quantum gate fidelity. One method is to work at so-called sweet spots, where the derivative of the splitting with respect to nearby gate voltages, and therefore the first-order coupling to charge noise, goes to zero, as in Reed et al. (2016), Martins et al. (2016), and Zajac et al. (2018). Another is to design a composite gate sequence in which coupling to charge noise and the qubit splitting are reduced; however, the two-qubit gate speed was unchanged in Nichol et al. (2017). The second direction is to use dynamical decoupling to reduce the effect of the low-frequency component of the noise (Güngördü & Kestner, 2018; Shulman et al., 2012; X. Wang et al., 2012).

Due to the difficulty of reducing the impact of charge noise, with the advent of isotopically purified silicon, qubits controlled by magnetic fields and largely decoupled from charge have made quick improvements in gate fidelity compared to more charge-like qubits. However, even these qubits have some coupling to charge, and their fidelities may ultimately be limited by charge noise. Furthermore, most of the two-qubit gates demonstrated so far are charge-based and thus experience decoherence through charge noise. Studying the source of charge noise and reducing it will therefore be essential for future scaling of these systems.

4.2. Readout

The two main readout techniques used for spin qubits were described in the sections introducing single-spin qubits and singlet–triplet qubits, the first measuring tunneling between the quantum dot and a charge reservoir and the second converting the spin state to a charge state. This section presents a more detailed discussion of the experimental implementations of these methods, as well as alternative readout technologies.

Both methods rely on a proximal quantum sensor, either a quantum point contact or a quantum dot. Connecting coaxial cables to the sensor can increase the measurement bandwidth, which can enable reduced measurement times. To capitalize on that, tank circuits are typically used to impedance match the 50Ω coaxial lines to the sensor quantum dot or QPC, which is maximally sensitive at resistances of h/e226kΩ and larger (Barthel et al., 2010). In this circuit, an inductor is connected in series with the sensor, and a capacitor is placed in parallel to ground. At the resonant frequency of ω1/LC, the impedance of the circuit appears to be 50Ω and the reflected signal is maximally sensitive to changes in the sensor’s impedance at the matching resistance R=L/C (Schoelkopf et al., 1998). In practice, it has been necessary to carefully adapt the circuit to each material and system architecture. This technique is straightforward to implement in GaAs/AlGaAs, reaching 98% fidelity in 1μs readout time for a singlet–triplet qubit using surface-mount inductors and the parasitic capacitance of the circuit board and 2DEG to ground (Barthel et al., 2009; Reilly et al., 2007; Shulman et al., 2014). Establishing readout with tank circuits in silicon devices has been more difficult, largely because the accumulation gates increase the parasitic capacitance in typical designs and most silicon 2DEGs, particularly the undoped varieties, are more resistive than their GaAs counterparts, both of which prevent the matching resistance from being at an optimal point for the sensor. There have now been several successful implementations of radio frequency readout in Si/SiGe, adjusting the device and circuit board design to improve sensitivity, achieving greater than 99% fidelity in 2μs for singlet–triplet readout (Connors et al., 2020; Liu et al., 2021; Noiri et al., 2020). Most of these have performed charge readout, distinguishing the singlet and triplet states with different charge configurations in a DQD. However, it is also possible to use tank circuits to speed up tunneling measurements, as demonstrated in Keith et al. (2019), where donor spin states are measured with 97% fidelity in 1.5μs.

An alternative approach is to use the qubit gate electrodes as sensors. This becomes particularly attractive as devices with more qubits are made because gate-based readout could substantially reduce the overhead associated with qubit readout. In this method, a tank circuit is connected to one of the gate electrodes. The reflected signal is sensitive to the quantum capacitance of the qubit dQ/dV, a measure of how the charge in a quantum dot moves when probed with a voltage pulse (Colless et al., 2013; Petersson, Smith, et al., 2010), making it useful for measuring electron tunneling. For this to be useful as a qubit measurement requires that the two qubit states have different quantum capacitances. These have been used to distinguish between the singlet and triplet states in several different varieties of silicon qubits, and single-shot readout for singlets and triplets has been achieved in both Si-MOS and donors, with fidelities of 70–85% (Ahmed et al., 2018; Crippa et al., 2019; Pakkiam et al., 2018; Schaal et al., 2018; Volk et al., 2019; West et al., 2019) A variant on this is to use cavity sensing through a superconducting resonator, using the same techniques as used with superconducting qubits in the “circuit QED” approach (Wallraff et al., 2005; Zheng et al., 2019).

4.3. Cavity Coupling

A major challenge for spin qubits is that qubit–qubit interactions are typically short range, relying on either exchange or capacitive coupling, which fall off on at most the micron scale. There are practical challenges to scaling systems in which all the quantum dots are adjacent, including that placing all the gate electrodes becomes nontrivial and the cross-talk between qubits makes control more complicated. Moreover, the ability to convert between stationary and flying qubits (qubits that can transmit quantum information across large distances, such as photons) is increasingly considered essential to a functional quantum computer (Hughes et al., 2004) because using photons to transmit quantum information is important for quantum communication and for the possibility of interfacing in hybrid quantum systems. Therefore, there has been a great push to develop some of the circuit QED methods that were extremely effective in superconducting qubits for spin qubits (Devoret & Schoelkopf, 2013).

In circuit QED, qubits are coupled to an electromagnetic resonator, typically a superconducting coplanar waveguide, which transmits information between the qubits coupled to it. It has been challenging to achieve strong coupling in spin qubits due to their reduced charge dipole moment compared to superconducting qubits and the high levels of charge noise in spin qubits that do have a large coupling to charge. Strong coupling to charge qubits was achieved first, with examples in both Si/SiGe (Mi, Cady, Zajac, Deelman, et al., 2017) and GaAs/AlGaAs (Stockklauser et al., 2017), the latter using a high-impedance SQUID resonator. High-impedance resonators have a larger voltage from each photon compared to 50Ω resonators, leading to increased interaction rates without directly increasing coupling to noise. Using resonators of 1001,000Ω allowed two varieties of spin qubits to reach strong coupling. In the first, a DQD variant of the micromagnet-controlled single-spin qubit in Si/SiGe was used (Mi et al., 2018; Samkharadze et al., 2018), which offered the low noise of a single-spin qubit and the increased gate speeds of a charge qubit. A second technique uses a triple quantum dot in GaAs, which has a large charge dipole (Landig et al., 2018).

One of the difficulties of establishing circuit QED architectures in spin qubits is the necessity of numerous gate electrodes to define the quantum dots. These can cause leakage from the resonator, leading to a low quality factor without careful filtering (Harvey-Collard et al., 2020; Mi, Cady, Zajac, Stehlik, et al., 2017). The requirements of spin qubit fabrication can also conflict with those of resonator fabrication, making the use of three-dimensional architectures with the resonator and qubits on separate chips appealing (Holman et al., 2020). Attaching multiple qubits to the same resonator is a particular challenge because the resonator changes the confinement potential on qubits. With a single qubit, the resonator’s voltage can be set to the value that optimizes the qubit’s properties, but with more qubits a single voltage must suffice for all of them. With clever engineering, however, these effects can be reduced, enabling two-qubit correlations to be measured, although a full two-qubit gate has not yet been demonstrated (Borjans, Croot, Mi, et al., 2020, Borjans, Croot, Putz, et al., 2020). A useful review expanding on these topics is given in Burkard et al. (2020).

4.4. Scaling

To perform useful algorithms, spin qubits will have to scale far beyond the current systems, increasing the number of qubits and gaining the ability to implement active error control (Brun, 2020). Although their similarity to the silicon transistor suggests that it may be possible to use industrial techniques to fabricate them in huge quantities, there remains a long way to go before that is feasible, making research on the pathway there essential. One of the greatest difficulties in building systems with large numbers of spin qubits is tuning the quantum dots to have the correct properties so that they can act as qubits; this includes the number of electrons and the tunnel coupling to the leads and to one another. These parameters can typically be controlled by gate electrode voltages, but the control is highly nonlinear and often even non-monotonic. Moreover, each parameter is controlled by multiple gates, and changing one parameter often changes another. There are also large variations from sample to sample, particularly in materials with more disorder. Together, this means that automating tuning is complicated. Due to the amount of work required to create an effective automated tuning program, for many years it was more efficient to rely on experienced researchers to tune QDs, but as the number of QDs in systems has increased, there has been a concerted effort to improve tuning algorithms.

Automated tuning has made progress across all of the key tasks for spin qubits. This includes the process of defining quantum dots (Baart et al., 2016; Lennon et al., 2019; Moon et al., 2020; Zwolak et al., 2020), adjusting the tunnel coupling (Hsiao et al., 2020; Teske et al., 2019; van Diepen et al., 2018), and measurement of the energy spectrum and location of charge transitions (Botzem et al., 2018). Another way to approach this problem is to design qubits where cross-talk is reduced, and each gate more directly controls a qubit property in a known way, which has been a benefit of the overlapping gate structure (Angus et al., 2007; Borselli et al., 2015; Zajac et al., 2015, 2016). Simulations have also been used to aid in designing such devices (Frees et al., 2019).

Once there are larger numbers of qubits in each device, new design questions become important. A number of papers have described architectures for arrays of qubits incorporating readout with minimal overhead and without compromising on control (Jones et al., 2012, 2018), including for donor qubits (Tosi et al., 2017) and Si-MOS (Li et al., 2018; Veldhorst et al., 2017). As the number of qubits increases and they are used to perform more complex algorithms, issues such as heating, noise from control electronics, and classical computer overhead can pose obstacles that will require careful consideration (Bluhm & Schreiber, 2019; Geck et al., 2019; Gonzalez-Zalba et al., 2020; Reilly, 2015; van Dijk et al., 2019). One particular focus has been building electronics that can function at cryogenic temperatures (Hornibrook et al., 2015; Pauka et al., 2021; Xue et al., 2020). One other achievement that may make these requirements less strenuous is the development of “hot” qubits in Si-MOS that work over 1 K (Petit et al., 2020; T. Yang et al., 2020). These architecture and wiring questions were reviewed together in Vandersypen and van Leeuwenhoek (2017).

One of the ultimate goals, of course, is to manufacture spin qubits with similar processes as computer chips. During the past decade, there have been demonstrations of spin qubits made using complementary MOS processes (Ciriano-Tejel et al., 2020; Maurand et al., 2016) as well as foundry-made quantum dots (Ansaloni et al., 2020). An Si-MOS spin qubit has also been fabricated using fully industry processing and showed similar noise levels to those made with standard techniques (Zwerver et al., 2021).

5. Conclusion

This article has attempted to give order to the wide variety of spin qubits. Because spin qubits share the same basic ingredients, many of the concepts are addressed in multiple sections; for instance, although exchange is used for single qubit gates in singlet–triplet and triple-dot qubits, it is the basis for many two-qubit gates in single-quantum-dot qubits. Moreover, developments in these qubits are interdependent, with progress in one often applicable to others. The evolution of spin qubits so far has suggested that future progress will come from many sources, including improvements in materials and fabrication, new qubit types and coupling schemes, and greater theoretical understanding of the system. Therefore, as the focus turns to building effective quantum information processors that can perform more powerful and complex algorithms, it is essential to have a broad understanding of the field.

Further Reading

  • Chatterjee, A., Stevenson, P., De Franceschi, S., Morello, A., de Leon, N., & Kuemmeth, F. (2020). Semiconductor qubits in practice. arXiv:2005.06564.
  • Hanson, R., Petta, J. R., Tarucha, S., & Vandersypen, L. M. K. (2007). Spins in few-electron quantum dots. Reviews of Modern Physics, 79, 1217–1265.
  • Kouwenhoven, L. P., Austing, D. G., & Tarucha, S. (2001). Few-electron quantum dots. Reports on Progress in Physics, 64, 701.
  • Ladd, T. D., & Carroll, M. S. (2018). Silicon qubits. In B. D. Guenther& D. G. Steel (Eds.), Encyclopedia of modern optics (2nd ed., pp. 467–477). Elsevier.
  • Zwanenburg, F. A., Dzurak, A. S., Morello, A., Simmons, M. Y., Hollenberg, L. C. L., Klimeck, G., Rogge, S., Coppersmith, S. N., & Eriksson, M. A. (2013). Silicon quantum electronics. Reviews of Modern Physics, 85, 961–1019.

References